# generated by Slic3r 1.36.2-prusa3d-linux64 on Fri Aug 18 17:28:12 2017
avoid_crossing_perimeters = 0
bed_shape = 0x0,210x0,210x297,0x297
bed_temperature = 110,110
before_layer_gcode = 
bottom_solid_layers = 3
bridge_acceleration = 2000
bridge_fan_speed = 0,0
bridge_flow_ratio = 0.9
bridge_speed = 0
brim_width = 12
clip_multipart_objects = 0
complete_objects = 0
cooling = 1,1
default_acceleration = 2000
deretract_speed = 40,40
disable_fan_first_layers = 3,3
dont_support_bridges = 1
duplicate_distance = 6
elefant_foot_compensation = 0
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n";"; Filament-specific end gcode \n;END gcode for filament\n"
end_gcode = ; end G-code, copied from BCN3D cura\nM104 T0 S0	;extruder heater off\nM104 T1 S0                     ;extruder heater off\nM140 S0                     ;heated bed heater off (if you have it)\nG91                                    ;relative positioning\nG1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure\nG1 Z+0.5 E-5 X-20 Y-20 F9000 ;move Z up a bit and retract filament even more\nG28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way\nM84                         ;steppers off\nG90                         ;absolute positioning
ensure_vertical_shell_thickness = 0
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0.5
external_perimeter_speed = 0
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 200
extruder_clearance_radius = 10
extruder_colour = ;
extruder_offset = 0x0,0x0
extrusion_axis = E
extrusion_multiplier = 0.9,0.9
extrusion_width = 0
fan_always_on = 0,0
fan_below_layer_time = 60,60
filament_colour = #393939;#393939
filament_cost = 0,0
filament_density = 0,0
filament_diameter = 2.85,2.85
filament_max_volumetric_speed = 0,0
filament_notes = ;
filament_settings_id = 
filament_soluble = 0,0
filament_type = ABS;ABS
fill_angle = 45
fill_density = 25%
fill_pattern = cubic
first_layer_acceleration = 1500
first_layer_bed_temperature = 110,110
first_layer_extrusion_width = 0.7
first_layer_height = 0.2
first_layer_speed = 30
first_layer_temperature = 270,270
gap_fill_speed = 0
gcode_comments = 1
gcode_flavor = reprap
infill_acceleration = 2000
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.55
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 0
interface_shells = 0
layer_gcode = 
layer_height = 0.2
max_fan_speed = 0,0
max_layer_height = 0,0
max_print_speed = 75
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 7
min_fan_speed = 0,0
min_layer_height = 0.07,0.07
min_print_speed = 10,10
min_skirt_length = 0
notes = 
nozzle_diameter = 0.4,0.5
octoprint_apikey = 
octoprint_host = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 1500
perimeter_extruder = 1
perimeter_extrusion_width = 0.5
perimeter_speed = 0
perimeters = 1
post_process = 
print_settings_id = 
printer_notes = ""
printer_settings_id = 
raft_layers = 0
resolution = 0
retract_before_travel = 2,2
retract_before_wipe = 0%,0%
retract_layer_change = 0,0
retract_length = 5,5
retract_length_toolchange = 5,5
retract_lift = 0.5,0.5
retract_lift_above = 0,0
retract_lift_below = 0,0
retract_restart_extra = 0,0
retract_restart_extra_toolchange = 0,0
retract_speed = 100,100
seam_position = aligned
serial_port = 
serial_speed = 250000
single_extruder_multi_material = 0
skirt_distance = 6
skirt_height = 1
skirts = 2
slowdown_below_layer_time = 10,10
small_perimeter_speed = 0
solid_infill_below_area = 30
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 0
spiral_vase = 0
standby_temperature_delta = -5
start_filament_gcode = "; Filament gcode\n";"; Filament gcode\n"
start_gcode = M104 S[first_layer_temperature] T1 ; set temperature\nM190 S[first_layer_bed_temperature] ; set bed heating\nG21        ;metric values\nG90        ;absolute positioning\nM107       ;start with the fan off\nG28 X0 Y0  ;move X/Y to min endstops\nG28 Z0     ;move Z to min endstops\nG1 Z15.0 F9000 ;move the platform down 15mm\nT1                      ;Switch to the 2nd extruder\nM109 S[first_layer_temperature] T1 ; set and wait for temperature\nG92 E0                  ;zero the extruded length\nG1 F200 E10             ;extrude 10mm of feed stock\nG92 E0                  ;zero the extruded length again\nG1 F9000
support_material = 0
support_material_angle = 0
support_material_buildplate_only = 1
support_material_contact_distance = 0
support_material_enforce_layers = 0
support_material_extruder = 2
support_material_extrusion_width = 0
support_material_interface_contact_loops = 0
support_material_interface_extruder = 2
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 0.5
support_material_speed = 0
support_material_synchronize_layers = 0
support_material_threshold = 60
support_material_with_sheath = 1
support_material_xy_spacing = 50%
temperature = 258,258
thin_walls = 1
threads = 4
toolchange_gcode = 
top_infill_extrusion_width = 0
top_solid_infill_speed = 0
top_solid_layers = 5
travel_speed = 300
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0,0
wipe_tower = 0
wipe_tower_per_color_wipe = 15
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0
z_offset = 0